Page 108 - Tanner Fasteners & Industrial Supplies Biig Book
P. 108

Anchors_2_17.qxp_Layout 1  8/21/17  2:56 PM  Page 100

                                                                                   SCREW ANCHORS





             WEDGE-BOLT +       Screw Anchors                         WEDGE-BOLT + HEX HEAD                         ®
                                                                                     ®
                            ®
        ANCHORS  The Wedge-Bolt®+ anchor is a one piece, heavy duty screw anchor with a  & Mechanically Galvanized)  discontinued for 2018 ™
                                                                      Carbon Steel, Zinc Plated (w/Blue Tip)
                                                                                                          Wedge-Bolt +
            finished hex head. Simple to install, easy to identify and fully removable.
                                                                                                        Replaced by SCREW-BOLT+
            It is designed for consistent and reliable performance in cracked and
                                                                                                         Please See P143 for Details
            uncracked concrete, as well as grouted masonry.
            • Wedge-Bolt+ is marked with a blue tip and must be installed
            with a matched tolerance Wedge-Bit.
            • Consistent performance in high & low strength concrete.  ITEM  CODE     DIAMETER SIZE        CLEARANCE    MIN.  THREAD      BOX     CTN.
            • Anchor can be installed through standard fixture holes.  CARBON                           GALVANIZED  & LENGTH                  HOLE DIA.  EMBED.  LENGTH       QTY.     QTY.
                                                                      POW 7204SD*                                 1/4" x 1-1/4"    5/16"          1”              1-1/8"     100  600
            • Wedge-Bit size is same as the nominal anchor diameter.  POW 7206SD*                                 1/4" x 1-3/4"    5/16"          1”              1-5/8"     100  600
            • Fast installation with powered impact wrench.           POW 7207SD                                    1/4" x 2"             5/16"          1-3/4”     2"             100  600
            • Diameter, length & identity marking stamped on head of 1 anchor.  POW 7208SD                                    1/4" x 2-1/4"    5/16"          1-3/4”     2"             100  600
                                                                      POW 7210SD                                    1/4" x 3"             5/16"          1-3/4”     2-3/4"     100  500
                                                                      POW 7220SD*                                 3/8" x 1-3/4"    7/16"          1-1/2"     1-1/2"     50     300
            Concrete, Block,           Tight Fit matches              POW 7222SD                                    3/8" x 2-1/2"    7/16"          2-1/8”     2-1/4"     50     300
            Brick                      standard fixture               POW 7224SD                                    3/8" x 3"             7/16"          2-1/8”     2-3/4"     50     250
            The Wedge-Bolt®+           holes                          POW 7226SD       POW 7726SD  3/8" x 4"             7/16"          2-1/8”     3-3/4"     50     250
            anchor is versatile        The Blue Tip                   POW 7228SD       POW 7728SD  3/8" x 5"             7/16"          2-1/8”     3-3/4"     50     250
            and can be used in a       Wedge-Bolt®+                   POW 7230SD       POW 7730SD  3/8" x 6"             7/16"          2-1/8”     3-3/4"     50     150
                                                                      POW 7240SD*                                 1/2" x 2"             9/16"          1-3/4"     1-3/4"     50     200
            variety of base            anchor is designed             POW 7242SD*                                 1/2" x 2-1/2"    9/16"          1-3/4"     2-1/4"     50     200
            materials. This reduces the need to stock   to match standard fixture clearance holes that  POW 7244SD                                    1/2" x 3"             9/16"          2-1/2"     2-3/4"     50     150
            assorted anchor types and learn a variety of  are 1/16” over nominal to provide a secure fit.  POW 7246SD       POW 7746SD  1/2" x 4"             9/16"          2-1/2"     3-3/4"     50     150
            installation procedures.   Since the Wedge-Bolt is specially matched to  POW 7248SD       POW 7748SD  1/2" x 5"             9/16"          2-1/2"     3-3/4"     25     100
                                       the clearance hole, the need for layout or hole  POW 7250SD       POW 7750SD  1/2" x 6"             9/16"          2-1/2"     3-3/4"     25      75
                                       spotting is eliminated.        POW 7268SD       POW 7751SD  1/2" x 6-1/2"    9/16"          2-1/2"                       25      75
            Close to edge                                             POW 7252SD       POW 7752SD  1/2" x 8"             9/16"          2-1/2"                       25      75
            installation               Immediate high                 POW 7260SD                                    5/8" x 3"             11/16"        2-1/2"     2-3/4"     25     100
            The Wedge Bolt®+           strength loading               POW 7262SD                                    5/8" x 4"             11/16"        3-1/4”     3-3/4"     25     100
            anchor cuts a thread       The Wedge-Bolt®+               POW 7264SD       POW 7764SD  5/8" x 5"             11/16"        3-1/4”     3-3/4"     25      75
            into the base mate-        anchor can be loaded           POW 7266SD       POW 7766SD  5/8" x 6"             11/16"        3-1/4”     3-3/4"     25      75
            rial. Since there are      immediately. Unlike                                             POW 7768SD  5/8” x 6-1/2”                                                               25      75
            no expansion forces, the Wedge-Bolt+ anchor  some adhesive   POW 7270SD       POW 7770SD  5/8" x 8"             11/16"        3-1/4”                       25      75
            can be installed closer to the edge than
                                       anchors, there is no          • *Sizes which are less than the minimum standard anchor length for strength design
            traditional mechanical anchors without  lengthy curing time.This allows for immediate  • Length of the anchor measured from under the head
            damaging the base material.
                                       completion of fastening applications.  • Wedge-Bolt+ is marked with a blue tip and must be  installed with a matched tolerance Wedge-Bit.
                                                                                Don’t Forget to Buy Wedge-Bits! Please turn to page 101
            One-piece design           Shallow
            The Wedge-Bolt®+           embedment depth
            anchor is a one-           The Wedge-Bolt®+               APPROVALS & LISTINGS
            piece unit which           anchor can be
            features a finished        installed at shallower        • International Code Council, Evaluation Service (ICC-ES), ESR-2526 for concrete. Code compliant with
            hex head formed            embedment depths               the 2015 IBC, 2015 IRC, 2012 IBC, 2012 IRC, 2009 IBC, 2009 IRC, 2006 IBC, 2006 IRC.
            with an integral           than traditional              • International Code Council, Evaluation Service (ICC-ES), ESR-1678 for concrete masonry code compliant
                                                                      with the 2012 IBC, 2012 IRC, 2009 IBC, 2009 IRC, 2006 IBC, 2006 IRC.
            washer, a patented dual lead thread, and a  wedge or sleeve anchors reducing the chance  • Tested in accordance with ACI 355.2 and ICC-ES AC193 for use in structural applications in concrete
            chamfered tip. A one-piece design eliminates
                                       of striking reinforcing bars or embedded   under the design provisions of ACI 318 (Strength Design method using Appendix D)
            the possibility of lost anchor parts or improper  cables. Drilling time and bit wear can be   • Evaluated and quali ed by an accredited independent testing laboratory for recognition in cracked and
            assembly.
                                       reduced resulting in significant savings.  uncracked concrete including seismic and wind loading (Category 1 anchors)
                                                                     • Evaluated and quali ed by an accredited independent testing labortatory for reliability against brittle
            Removable and              Diameter & length ID           failure, e.g. hydrogen embrittlement
                                                                     • Tested in accordance with ASTM E488 and AC106 criteria
            reusable                   Wedge-Bolt®+
            The Wedge-Bolt®+           anchors have both              MATERIAL SPECIFICATIONS
            anchor is easy to          the diameter and               Anchor Component             Specification
        100ANCHORS
            remove, leaving a
                                       length clearly
                                                                      Anchor body &
            neat clean hole.
                                                                                       Case hardened carbon steel
                                       embossed on the head
            Unlike traditional
                                       of the anchor. This enables simple and easy
                                                                      hex washer head
                                       inspection.
            anchors no grinding off of anchors is needed
                                                                                       Zinc plating according to ASTM B 633, SC1, Type III (Fe/Zn 5)
                                                                      Plating
            and no anchor components are left in the hole.
                                                                                       Minimum plating requirment for Mild Service Condition
            If requiredWedge-Bolts can be reinstalled in
                                                                                       Mechanically galvanized zinc plating according to
            the same hole after adjustment of the fixture.
           800 456-2658         email: sales@tannerbolt.com        www.shoptanner.com   ASTM B 695, Class 55
                                   714 Montauk Ave., Brooklyn,  NY 11208    718 434-4500   Fax: 718 434-3215
                                    60-01 55th Drive, Maspeth, NY 11378    718 786-2050   Fax: 718 228-7297
                                                     800 3rd Ave., Brooklyn, NY 11232    929 337-1821
   103   104   105   106   107   108   109   110   111   112   113