Page 159 - Tanner Fasteners & Industrial Supplies Biig Book
P. 159

Security Catalog 2_17.qxp_Layout 1  8/18/17  12:32 PM  Page 151

            SECURITY PRODUCTS





                                                                                                      ®
              ULTRACON    ®                    Torx Tamper-Resistant Drive  Button Head            Silver Stalgard Finish
                                       ®
                                                                        ITEM                                      SIZE  DRIVER        BOX                    ITEM  CTN.
              Masonry Concrete Screws                                   CODE              SIZE              QTY.          CODE                                                         QTY.
                                                                        25N125ABTZ     1/4" x 1-1/4"         27TXH     100              25N125ABTZ/BULK             3000
                  ®
               Torx Tamper-Resistant UltraCon Masonry Screws            25N175ABTZ     1/4" x 1-3/4"    27TXH    100        25N175ABTZ/BULK     2000
                                      ®
               are the optimal fastening solution for use in concrete,  25N225ABTZ      1/4" x 2-1/4"    27TXH    100        25N225ABTZ/BULK    1500
                                                                        25N275ABTZ      1/4" x 2-3/4"    27TXH    100    25N275ABTZ/BULK   1000
               brick, or hollow block. This unique screw combines
                                                                                                     ®
                                   ®
               the security feature of a Torx tamper-resistant         Flat Head               Silver Stalgard Finish
               drive with the superior quality and easy                 25N125AFTZ     1/4" x 1-1/4"    27TXH     100        25N125AFTZ/BULK    3000
                                 ®
               installation of an UltraCon masonry screw.               25N175AFTZ     1/4" x 1-3/4"    27TXH     100        25N175AFTZ/BULK    2500
                                                                        25N225AFTZ      1/4" x 2-1/4"    27TXH     100        25N225AFTZ/BULK    1500
               The special Hi-Lo thread literally taps threads into     25N275AFTZ      1/4" x 2-3/4"    27TXH    100        25N275AFTZ/BULK    1000
               masonry materials. The high, sharp thread with its       25N325AFTZ*    1/4" x 3-1/4"    27TXH    100        25N325AFTZ/BULK*  1000
               notched cutting edge cuts deeply and easily. The        • *Available in zinc plated only
               alternating low thread provides stability for fast,
                                                                       Drill Bits & Installation Tools
               accurate driving.
                                        ®
               The screws are coated with Stalgard finish to provide superior corrosion
               resistance. Fasteners coated with Stalgard finish typically show no red rust
                                            ®
                                                                        ITEM                            BOX
               or other base material corrosion on significant surfaces even after 800 hours  CODE    DESCRIPTION  QTY.
               of 5% neutral salt spray exposure (ASTM B117).          27TXH     #27 Torx Tamper-Resistant Hex Bit  1
                                                                       ELC ELT405  3/16" x 3-1/2" Straight Shank Tanged Bit  1
                                                                       ELC ELT415  3/16" x 4-1/2" Straight Shank Tanged Bit  1
              Installation                                             ELC ELT630         3/16" x 5" SDS Carbide Drill Bit  1
              Fastener Length and Diameter
              The length of the UltraCon fastener to be used is determined by combining the thickness of
                             ®
              the attachment (A) with the desired depth of embedment in the masonry material (B). It is   Mechanical Properties
                                              recommended that a minimum of 1”  NOMINAL              THREAD             THREAD   UNLEADED      FY*                     FU*
                                                                       DIAMETER            O.D.                     I.D.      SHANK               MATERIAL    HEAT TREATMENT               TENSILE            TENSILE
                                                                                                             YIELD                YIELD
                                                                              NOMINAL          NOMINAL     NOMINAL
                              A = Attachment thickness  and a maximum of 1-3/4” embedment  1/4                   .255             .161           .189           1022         Case Hardened        155 K.S.I.    177 K.S.I.
                                     ®
                              B = UltraCon embedment    be used in determining  fastener      Carbon     (HRC 52min. with
                                (min. of 1”, max. of   length. The diameter of the fastener    Steel         core hardness of
                                 1-3/4”)      and the depth of embedment affect
                                                                                                   HRC 32 - 40 mx.)
                                       ®
                              A+B = UltraCon length  pullout strengths.  Application
                              B+C = Hole depth   strength requirements and safety  • Values listed are based on numerous tests with all three diameters of UltraCon® fasteners. Testing
                                  (must be at least   factors should be considered when  was done per ASTM E8-96 standards. The yield  and ultimate tensile values shown are indicative of
                                  1/4” deeper   determining the depth of embedment  the hardness levels obtained.
                                  than UltraCon ®   and fastener diameter.
                                  embedment)
                                              Please reference the Performance Data chart  PERFORMANCE DATA: 1/4” Screw Diameter
              Hole Depth                                                Hollow Block 1,924psi          Concrete 2,730psi
              The correct hole depth (B & C) can normally be obtained by drilling the full length of this bit.  DEPTH OF    EDGE  DEPTH OF         EDGE
              In all cases, the hole must be at least 1/4” deeper than the depth of the fastener embedment.  DIA.               EMBEDMENT   DIST.       PULL-OUT  SHEAR  EMBEDMENT   DIST.              PULL-OUT           SHEAR
                                                                                                 1”                                       668            632
              Normal safety precautions should be observed when drilling the holes to avoid
                                                                                  1"              998           900  1-3/8"      1”                1,166        1,070
              electrical installations, other utilities and reinforcement bars.
                                                                                                 1-3/4"                          1,857            919
              Hole Diameter                                            1/4"          1-1/4"
                                                                                                 1”                                       809        1,153
              The diameter of the drilled hole is also important to the performance of the UltraCon ®  2-1/2”       709       1,486  1-3/8"       2-1/2”      1,507         1,583
              masonry fastener.  To provide the proper hole diameters, Elco carbide-tipped drill bits are  1-3/4"                          1,908         1,780
                                                 ®
              manufactured to closer standards than those called for in the American National Standard.
              Using Elco carbide-tipped bits will help assure consistent performance and maximum   • Note: Indicated pull-out and shear failure values were obtained in tests witnessed by
                    ®
                                                                       independent test labs (see below). These figures are offered only as a guide and are not
              pullout strength.
                                                                       guaranteed in any way by Tanner Fasteners & Industrial Products. A safety factor of 4:1,
                                                                       or 25% of ultimate pull-out value, is generally accepted as a safe working load; however,
                                                                       reference should always be made to applicable codes for the specific safe working ratio.
              Installation Tools
                                                                      TEST REPORT: Cross-Reference Information
                                                                             Concrete                                Block
                                                                        UltraCon®                   Dia. Test report no.*  UltraCon®              Dia. Test report no.*
                                                                         1/4"                                  HETI 03-1136                           1/4"                             HETI 03-1159
                ITEM  CODE    DESCRIPTION
               ELC ELP100  Two piece for all sizes and head styles    * Testing by Hurricane Engineering & Testing, Inc. (HETI).
                                                                      Additional testing has been done in other materials and conditions and is available upon request.
                                                                                                                             151
                                                 www.shoptanner.com         email: sales@tannerbolt.com        800 456-2658
                                                 714 Montauk Ave., Brooklyn,  NY 11208    718 434-4500   Fax: 718 434-3215
                                                 60-01 55th Drive, Maspeth, NY 11378    718 786-2050   Fax: 718 228-7297
                                                 800 3rd Ave., Brooklyn, NY 11232  929 337-1821
   154   155   156   157   158   159   160   161   162   163   164