Page 98 - Tanner Fasteners & Industrial Supplies Biig Book
P. 98

Anchors_2_17.qxp_Layout 1  8/21/17  2:53 PM  Page 90

                                                                        EXPANSION ANCHORS





             POWER-STUD + SD1 & SD2               Strength Design Wedge Expansion Anchors
                            ™
        ANCHORS  The Power-Stud + anchors are fully threaded, torque-controlled, wedge   • Consistent performance in high and low strength concrete

            expansion anchors that are designed for consistent performance in cracked
                                                                     • Nominal drill bit size is same as anchor diameter.
            and uncracked concrete. Suitable base materials include normal-weight
                                                                     • Length ID code and identifying marking stamped on head of anchor
                                                                     • Installed through standard fixture holes
            concrete, structural sand-lightweight concrete and concrete over metal deck.
                                                                     • Design allows for follow-up expansion after setting under tensile loading
           Installation:
           1.Using the proper drill bit size, drill a hole into the base  material to the   Be sure the anchor is driven to the minimum required nominal
             required depth. The tolerances of the drill bit used should meet the   embedment depth.
             requirements of ANSI Standard B212.15                    4. Tighten anchor with torque wrench applying required installation torque.
             2. Remove dust and debris from the hole.
             3. Position the washer on the anchor and attach the nut. If installing
              through a fixture, drive the anchor through the fixture in to the hole.



             POWER-STUD+ SD1
             Carbon Steel Body & Expansion Clip




            ITEM                                              SIZE                                           THREAD            CARBIDE  BOX  CTN.
            CODE                  LENGTH             BIT SIZE  QTY.  QTY.   APPROVALS & LISTINGS - SD1 & SD2
            POW 7400SD1*           1/4" x 1-3/4"             3/4"  1/4" x 4"               100     600
            POW 7402SD1             1/4" x 2-1/4"             1-1/4"  1/4" x 6"               100     600   • International Code Council, Evaluation Service (ICC-ES), ESR-2818 for concrete Code compliant with
            POW 7404SD1             1/4" x 3-1/4"             2-1/4"  1/4" x 6"               100     600   the 2015 IBC, 2015 IRC, 2012 IBC, 2012 IRC, 2009 IBC, 2009 IRC, 2006 IBC and 2006 IRC.
            POW 7410SD1*           3/8" x 2-1/4"             7/8"  3/8" x 6"               50       300   • International Code Council, Evaluation Service (ICC-ES), ESR-2966 for masonry Code compliant with
            POW 7412SD1*           3/8" x 2-3/4"             1-3/8"  3/8" x 6"               50       300   the 2012 IBC, 2012 IRC, 2009 IBC, 2009 IRC, 2006 IBC, and 2006 IRC.
            POW 7413SD1             3/8" x 3"                      1-5/8"  3/8" x 6"               50       300   • Tested in accordance with ACI 355.2/ASTM E 488 and ICC-ES AC193 for use in structural concrete
            POW 7414SD1             3/8" x 3-1/2"             2-1/8"  3/8" x 6"               50       300   under the design provisions of ACI 318 (Strength Design method using Appendix D)
            POW 7415SD1             3/8" x 3-3/4               2-3/8"  3/8" x 6"               50       300   • Evaluated and quali ed by an accredited independent testing laboratory for recognition in cracked
            POW 7416SD1             3/8" x 5"                      3-5/8"  3/8" x 10"            50       300   and uncracked concrete including seismic and wind loading (Category 1 anchors)
            POW 7417SD1             3/8" x 7"                      5-5/8"  3/8" x 10"            50       200   • Tested in accordance with ICC-ES AC01 for use in Masonry
            POW 7420SD1*           1/2" x 2-3/4"             1"  1/2" x 6"               50       200   • Underwriters Laboratories (UL Listed) - File No. EX1289. See listing for sizes
            POW 7422SD1             1/2" x 3-3/4"             2"  1/2" x 6"               50       200
            POW 7423SD1             1/2" x 4-1/2"             2-3/4"  1/2" x 10"            50       200
            POW 7424SD1             1/2" x 5-1/2"             3-3/4"  1/2" x 10"            50       150
            POW 7426SD1             1/2" x 7"                      5-1/4"  1/2" x 12"            25       100
            POW 7427SD1             1/2" x 8-1/2"             6-3/4"  1/2" x 12"            25       100  MATERIAL SPECIFICATIONS - SD1 & SD2
            POW 7428SD1             1/2" x 10"                   6-3/4"  1/2" x 12"            25       100
            POW 7430SD1*           5/8" x 3-1/2"             1-1/2"  5/8 x 8”                 25       100   ANCHOR COMPONENT  SPECIFICATION
            POW 7432SD1             5/8" x 4-1/2"             2-1/2"  5/8 x 8”                 25       100   Anchor Body  Medium Carbon Steel
            POW 7433SD1             5/8" x 5"                      3"  5/8 x 8”                 25       100
            POW 7434SD1             5/8" x 6"                      4"  5/8 x 8”                 25        75   Hex Nut  Carbon steel, ASTM A 563, Grade A
            POW 7436SD1             5/8" x 7"                      5"  5/8 x 12”               25        75   Washer  Carbon steel, ASTM F 844; meets dimensional requirements
            POW 7438SD1             5/8" x 8-1/2"             6-1/2"  5/8 x 12”               25        50  of ANSI B18.22.2, Type A plain
            POW 7439SD1             5/8" x 10"                   8"  5/8 x 12”               25       50   Expansion Wedge (clip) SD1-Carbon Steel          SD2-Stainess Steel
            POW 7440SD1*           3/4" x 4-1/4"             1-3/4"  3/4 x 8”                 20       60   • * Denotes sizes
            POW 7441SD1*           3/4" x 4-3/4"             2-1/4"  3/4 x 8”                 20       60   which are less than  Plating  Zinc plating according to ASTM B 633,  SC1, Type III (Fe/Zn 5)
            POW 7442SD1             3/4" x 5-1/2"             3"  3/4 x 8”                 20       60   the minimum stan-  Minimum plating requirement for Mild Service Condition
            POW 7444SD1             3/4" x 6-1/4"             3-3/4"  3/4 x 12”               20       60   dard anchor length
            POW 7446SD1             3/4" x 7"                      4-1/2"  3/4 x 12”               20       60   for strength design
            POW 7448SD1             3/4" x 8-1/2"             6"  3/4 x 12”               10       40   • The published size
            POW 7449SD1             3/4" x 10"                   7-1/2"  3/4 x 12”               10       30   includes the diameter  TIE WIRE POWER-STUD+ SD1
            POW 7451SD1             3/4" x 12"                   9-1/2"  3/4 x 18”               10       30   and the overall   Carbon Steel Body & Expansion Clip
         90ANCHORS                                                                                   BOX     CTN.
                                                         length of the anchor.
            POW 7450SD1             7/8" x 6"                      2-3/4”
                                       7/8 x 12”               10       40
                                       7/8 x 12”               10       40
            POW 7452SD1#           7/8" x 8"                      4-3/4”
                                                         • Allow for fixture
                                       7/8 x 18”               10       30
            POW 7454SD1#           7/8" x 10"                   6-3/4”
                                                         thickness plus one
                                                         anchor diameter for
            POW 7461SD1*           1" x 6"                          2-3/8"
                                       1 x 10”                   10       30
                                                                      SPECIFICATIONS
                                                         the nut and washer
            POW 7463SD1             1" x 9"                          5-3/8"
                                       1 x 12”                   10       30
                                                                                              THREAD
                                                                                  SIZE
                                                                      ITEM
                                                         thickness when
                                       1 x 18”                   5         15
            POW 7465SD1             1" x 12"                       8-3/8"
                                                                                                     QTY.
                                                                      NO.
                                                                                              LENGTH
                                                                                                             QTY.
                                                         selecting a length.
                                       1-1/4 x 15”          5         15
            POW 7473SD1#           1-1/4" x 9"                 4-3/4”
                                                                     POW 7409SD1                  1/4"                                     n/a                    100                    500
                                       1-1/4 x 22-1/2”   5         15
            POW 7475SD1#           1-1/4" x 12"               7-3/4”
                                                         • # ICC-ES Pending
           800 456-2658         email: sales@tannerbolt.com        www.shoptanner.com
                                   714 Montauk Ave., Brooklyn,  NY 11208    718 434-4500   Fax: 718 434-3215
                                    60-01 55th Drive, Maspeth, NY 11378    718 786-2050   Fax: 718 228-7297
                                                     800 3rd Ave., Brooklyn, NY 11232    929 337-1821
   93   94   95   96   97   98   99   100   101   102   103